Changelog for
wpa_supplicant-gui-2.6-89.7.i586.rpm :
Thu Oct 6 14:00:00 2016 meissnerAATTsuse.com
- updated to 2.6 / 2016-10-02
* fixed WNM Sleep Mode processing when PMF is not enabled
[http://w1.fi/security/2015-6/] (CVE-2015-5310 bsc#952254)
* fixed EAP-pwd last fragment validation
[http://w1.fi/security/2015-7/] (CVE-2015-5315 bsc#953115)
* fixed EAP-pwd unexpected Confirm message processing
[http://w1.fi/security/2015-8/] (CVE-2015-5316 bsc#953115)
* fixed WPS configuration update vulnerability with malformed passphrase
[http://w1.fi/security/2016-1/] (CVE-2016-4476 bsc#978172)
* fixed configuration update vulnerability with malformed parameters set
over the local control interface
[http://w1.fi/security/2016-1/] (CVE-2016-4477 bsc#978175)
* fixed TK configuration to the driver in EAPOL-Key 3/4 retry case
* extended channel switch support for P2P GO
* started to throttle control interface event message bursts to avoid
issues with monitor sockets running out of buffer space
* mesh mode fixes/improvements
- generate proper AID for peer
- enable WMM by default
- add VHT support
- fix PMKID derivation
- improve robustness on various exchanges
- fix peer link counting in reconnect case
- improve mesh joining behavior
- allow DTIM period to be configured
- allow HT to be disabled (disable_ht=1)
- add MESH_PEER_ADD and MESH_PEER_REMOVE commands
- add support for PMKSA caching
- add minimal support for SAE group negotiation
- allow pairwise/group cipher to be configured in the network profile
- use ieee80211w profile parameter to enable/disable PMF and derive
a separate TX IGTK if PMF is enabled instead of using MGTK
incorrectly
- fix AEK and MTK derivation
- remove GTKdata and IGTKdata from Mesh Peering Confirm/Close
- note: these changes are not fully backwards compatible for secure
(RSN) mesh network
* fixed PMKID derivation with SAE
* added support for requesting and fetching arbitrary ANQP-elements
without internal support in wpa_supplicant for the specific element
(anqp[265]=
in \"BSS \" command output)
* P2P
- filter control characters in group client device names to be
consistent with other P2P peer cases
- support VHT 80+80 MHz and 160 MHz
- indicate group completion in P2P Client role after data association
instead of already after the WPS provisioning step
- improve group-join operation to use SSID, if known, to filter BSS
entries
- added optional ssid= argument to P2P_CONNECT for join case
- added P2P_GROUP_MEMBER command to fetch client interface address
* P2PS
- fix follow-on PD Response behavior
- fix PD Response generation for unknown peer
- fix persistent group reporting
- add channel policy to PD Request
- add group SSID to the P2PS-PROV-DONE event
- allow \"P2P_CONNECT p2ps\" to be used without specifying the
default PIN
* BoringSSL
- support for OCSP stapling
- support building of h20-osu-client
* D-Bus
- add ExpectDisconnect()
- add global config parameters as properties
- add SaveConfig()
- add VendorElemAdd(), VendorElemGet(), VendorElemRem()
* fixed Suite B 192-bit AKM to use proper PMK length
(note: this makes old releases incompatible with the fixed behavior)
* improved PMF behavior for cases where the AP and STA has different
configuration by not trying to connect in some corner cases where the
connection cannot succeed
* added option to reopen debug log (e.g., to rotate the file) upon
receipt of SIGHUP signal
* EAP-pwd: added support for Brainpool Elliptic Curves
(with OpenSSL 1.0.2 and newer)
* fixed EAPOL reauthentication after FT protocol run
* fixed FTIE generation for 4-way handshake after FT protocol run
* extended INTERFACE_ADD command to allow certain type (sta/ap)
interface to be created
* fixed and improved various FST operations
* added 80+80 MHz and 160 MHz VHT support for IBSS/mesh
* fixed SIGNAL_POLL in IBSS and mesh cases
* added an option to abort an ongoing scan (used to speed up connection
and can also be done with the new ABORT_SCAN command)
* TLS client
- do not verify CA certificates when ca_cert is not specified
- support validating server certificate hash
- support SHA384 and SHA512 hashes
- add signature_algorithms extension into ClientHello
- support TLS v1.2 signature algorithm with SHA384 and SHA512
- support server certificate probing
- allow specific TLS versions to be disabled with phase2 parameter
- support extKeyUsage
- support PKCS #5 v2.0 PBES2
- support PKCS #5 with PKCS #12 style key decryption
- minimal support for PKCS #12
- support OCSP stapling (including ocsp_multi)
* OpenSSL
- support OpenSSL 1.1 API changes
- drop support for OpenSSL 0.9.8
- drop support for OpenSSL 1.0.0
* added support for multiple schedule scan plans (sched_scan_plans)
* added support for external server certificate chain validation
(tls_ext_cert_check=1 in the network profile phase1 parameter)
* made phase2 parser more strict about correct use of auth= and
autheap= values
* improved GAS offchannel operations with comeback request
* added SIGNAL_MONITOR command to request signal strength monitoring
events
* added command for retrieving HS 2.0 icons with in-memory storage
(REQ_HS20_ICON, GET_HS20_ICON, DEL_HS20_ICON commands and
RX-HS20-ICON event)
* enabled ACS support for AP mode operations with wpa_supplicant
* EAP-PEAP: fixed interoperability issue with Windows 2012r2 server
(\"Invalid Compound_MAC in cryptobinding TLV\")
* EAP-TTLS: fixed success after fragmented final Phase 2 message
* VHT: added interoperability workaround for 80+80 and 160 MHz channels
* WNM: workaround for broken AP operating class behavior
* added kqueue(2) support for eloop (CONFIG_ELOOP_KQUEUE)
* nl80211:
- add support for full station state operations
- do not add NL80211_ATTR_SMPS_MODE attribute if HT is disabled
- add NL80211_ATTR_PREV_BSSID with Connect command
- fix IEEE 802.1X/WEP EAP reauthentication and rekeying to use
unencrypted EAPOL frames
* added initial MBO support; number of extensions to WNM BSS Transition
Management
* added support for PBSS/PCP and P2P on 60 GHz
* Interworking: add credential realm to EAP-TLS identity
* fixed EAPOL-Key Request Secure bit to be 1 if PTK is set
* HS 2.0: add support for configuring frame filters
* added POLL_STA command to check connectivity in AP mode
* added initial functionality for location related operations
* started to ignore pmf=1/2 parameter for non-RSN networks
* added wps_disabled=1 network profile parameter to allow AP mode to
be started without enabling WPS
* wpa_cli: added action script support for AP-ENABLED and AP-DISABLED
events
* improved Public Action frame addressing
- add gas_address3 configuration parameter to control Address 3
behavior
* number of small fixes
- wpa_supplicant-dump-certificate-as-PEM-in-debug-mode.diff: dump x509
certificates from remote radius server in debug mode in WPA-EAP.
Wed Jul 20 14:00:00 2016 tchvatalAATTsuse.com
- Remove support for <12.3 as we are unresolvable there anyway
- Use qt5 on 13.2 if someone pulls this package in
- Convert to pkgconfig dependencies over the devel pkgs
- Use the %qmake5 macro to build the qt5 gui
Mon May 23 14:00:00 2016 michal.hruseckyAATTopensuse.org
- add non-D-Bus service file
Wed Mar 23 13:00:00 2016 lnusselAATTsuse.de
- add After=dbus.service to prevent too early shutdown (bnc#963652)
Fri Feb 26 13:00:00 2016 crrodriguezAATTopensuse.org
- Revert CONFIG_ELOOP_EPOLL=y, it is broken in combination
with CONFIG_DBUS=yes.
Sat Feb 20 13:00:00 2016 crrodriguezAATTopensuse.org
- spec: Compile the GUI against QT5 in 13.2 and later.
Thu Feb 18 13:00:00 2016 crrodriguezAATTopensuse.org
- Previous update did not include version 2.5 tarball
or changed the version number in spec, only the changelog
and removed patches.
- config: set CONFIG_NO_RANDOM_POOL=y, we have a reliable·
random number generator by using /dev/urandom, no need to
keep an internal random number pool which draws entropy from
/dev/random.
- config: prefer using epoll(7) instead of select(2)
by setting CONFIG_ELOOP_EPOLL=y
- wpa_supplicant-getrandom.patch: Prefer to use the getrandom(2)
system call to collect entropy. if it is not present disable
buffering when reading /dev/urandom, otherwise each os_get_random()
call will request BUFSIZ of entropy instead of the few needed bytes.
Wed Feb 17 13:00:00 2016 lnusselAATTsuse.de
- add aliases for both provided dbus names to avoid systemd stopping the
service when switching runlevels (boo#966535)
Thu Feb 4 13:00:00 2016 michaelAATTstroeder.com
- removed obsolete security patches:
* 0001-P2P-Validate-SSID-element-length-before-copying-it-C.patch
* 0001-WPS-Fix-HTTP-chunked-transfer-encoding-parser.patch
* 0001-AP-WMM-Fix-integer-underflow-in-WMM-Action-frame-par.patch
* 0001-EAP-pwd-peer-Fix-payload-length-validation-for-Commi.patch
* wpa_s-D-Bus-Fix-operations-when-P2P-management-interface-is-used.patch
* 0002-EAP-pwd-server-Fix-payload-length-validation-for-Com.patch
* 0003-EAP-pwd-peer-Fix-Total-Length-parsing-for-fragment-r.patch
* 0004-EAP-pwd-server-Fix-Total-Length-parsing-for-fragment.patch
* 0005-EAP-pwd-peer-Fix-asymmetric-fragmentation-behavior.patch
- Update to upstream release 2.5
* fixed P2P validation of SSID element length before copying it
[http://w1.fi/security/2015-1/] (CVE-2015-1863)
* fixed WPS UPnP vulnerability with HTTP chunked transfer encoding
[http://w1.fi/security/2015-2/] (CVE-2015-4141)
* fixed WMM Action frame parser (AP mode)
[http://w1.fi/security/2015-3/] (CVE-2015-4142)
* fixed EAP-pwd peer missing payload length validation
[http://w1.fi/security/2015-4/]
(CVE-2015-4143, CVE-2015-4144, CVE-2015-4145, CVE-2015-4146)
* fixed validation of WPS and P2P NFC NDEF record payload length
[http://w1.fi/security/2015-5/]
* nl80211:
- added VHT configuration for IBSS
- fixed vendor command handling to check OUI properly
- allow driver-based roaming to change ESS
* added AVG_BEACON_RSSI to SIGNAL_POLL output
* wpa_cli: added tab completion for number of commands
* removed unmaintained and not yet completed SChannel/CryptoAPI support
* modified Extended Capabilities element use in Probe Request frames to
include all cases if any of the values are non-zero
* added support for dynamically creating/removing a virtual interface
with interface_add/interface_remove
* added support for hashed password (NtHash) in EAP-pwd peer
* added support for memory-only PSK/passphrase (mem_only_psk=1 and
CTRL-REQ/RSP-PSK_PASSPHRASE)
* P2P
- optimize scan frequencies list when re-joining a persistent group
- fixed number of sequences with nl80211 P2P Device interface
- added operating class 125 for P2P use cases (this allows 5 GHz
channels 161 and 169 to be used if they are enabled in the current
regulatory domain)
- number of fixes to P2PS functionality
- do not allow 40 MHz co-ex PRI/SEC switch to force MCC
- extended support for preferred channel listing
* D-Bus:
- fixed WPS property of fi.w1.wpa_supplicant1.BSS interface
- fixed PresenceRequest to use group interface
- added new signals: FindStopped, WPS pbc-overlap,
GroupFormationFailure, WPS timeout, InvitationReceived
- added new methods: WPS Cancel, P2P Cancel, Reconnect, RemoveClient
- added manufacturer info
* added EAP-EKE peer support for deriving Session-Id
* added wps_priority configuration parameter to set the default priority
for all network profiles added by WPS
* added support to request a scan with specific SSIDs with the SCAN
command (optional \"ssid \" arguments)
* removed support for WEP40/WEP104 as a group cipher with WPA/WPA2
* fixed SAE group selection in an error case
* modified SAE routines to be more robust and PWE generation to be
stronger against timing attacks
* added support for Brainpool Elliptic Curves with SAE
* added support for CCMP-256 and GCMP-256 as group ciphers with FT
* fixed BSS selection based on estimated throughput
* added option to disable TLSv1.0 with OpenSSL
(phase1=\"tls_disable_tlsv1_0=1\")
* added Fast Session Transfer (FST) module
* fixed OpenSSL PKCS#12 extra certificate handling
* fixed key derivation for Suite B 192-bit AKM (this breaks
compatibility with the earlier version)
* added RSN IE to Mesh Peering Open/Confirm frames
* number of small fixes
Thu May 7 14:00:00 2015 roAATTsuse.de
- added patch for bnc#930077
0001-AP-WMM-Fix-integer-underflow-in-WMM-Action-frame-par.patch
- added patch for bnc#930078
0001-WPS-Fix-HTTP-chunked-transfer-encoding-parser.patch
- added patches for bnc#930079
0001-EAP-pwd-peer-Fix-payload-length-validation-for-Commi.patch
0002-EAP-pwd-server-Fix-payload-length-validation-for-Com.patch
0003-EAP-pwd-peer-Fix-Total-Length-parsing-for-fragment-r.patch
0004-EAP-pwd-server-Fix-Total-Length-parsing-for-fragment.patch
0005-EAP-pwd-peer-Fix-asymmetric-fragmentation-behavior.patch
Fri May 1 14:00:00 2015 zaitorAATTopensuse.org
- Add wpa_s-D-Bus-Fix-operations-when-P2P-management-interface-is-used.patch
Fix Segmentation fault in wpa_supplicant. Patch taken from
upstream master git (arch#44740).
Thu Apr 23 14:00:00 2015 crrodriguezAATTopensuse.org
- 0001-P2P-Validate-SSID-element-length-before-copying-it-C.patch
Fix CVE-2015-1863, memcpy overflow.
- wpa_supplicant-alloc_size.patch: annotate two wrappers
with attribute alloc_size, which may help warning us of
bugs such as the above.
Fri Apr 10 14:00:00 2015 stefan.bruensAATTrwth-aachen.de
- Delete wpa_priv and eapol_test man pages, these are disabled in config
- Move wpa_gui man page to gui package
Thu Apr 2 14:00:00 2015 stefan.bruensAATTrwth-aachen.de
- Update to 2.4
* allow OpenSSL cipher configuration to be set for internal EAP server
(openssl_ciphers parameter)
* fixed number of small issues based on hwsim test case failures and
static analyzer reports
* P2P:
- add new=<0/1> flag to P2P-DEVICE-FOUND events
- add passive channels in invitation response from P2P Client
- enable nl80211 P2P_DEVICE support by default
- fix regresssion in disallow_freq preventing search on social
channels
- fix regressions in P2P SD query processing
- try to re-invite with social operating channel if no common channels
in invitation
- allow cross connection on parent interface (this fixes number of
use cases with nl80211)
- add support for P2P services (P2PS)
- add p2p_go_ctwindow configuration parameter to allow GO CTWindow to
be configured
* increase postponing of EAPOL-Start by one second with AP/GO that
supports WPS 2.0 (this makes it less likely to trigger extra roundtrip
of identity frames)
* add support for PMKSA caching with SAE
* add support for control mesh BSS (IEEE 802.11s) operations
* fixed number of issues with D-Bus P2P commands
* fixed regression in ap_scan=2 special case for WPS
* fixed macsec_validate configuration
* add a workaround for incorrectly behaving APs that try to use
EAPOL-Key descriptor version 3 when the station supports PMF even if
PMF is not enabled on the AP
* allow TLS v1.1 and v1.2 to be negotiated by default; previous behavior
of disabling these can be configured to work around issues with broken
servers with phase1=\"tls_disable_tlsv1_1=1 tls_disable_tlsv1_2=1\"
* add support for Suite B (128-bit and 192-bit level) key management and
cipher suites
* add WMM-AC support (WMM_AC_ADDTS/WMM_AC_DELTS)
* improved BSS Transition Management processing
* add support for neighbor report
* add support for link measurement
* fixed expiration of BSS entry with all-zeros BSSID
* add optional LAST_ID=x argument to LIST_NETWORK to allow all
configured networks to be listed even with huge number of network
profiles
* add support for EAP Re-Authentication Protocol (ERP)
* fixed EAP-IKEv2 fragmentation reassembly
* improved PKCS#11 configuration for OpenSSL
* set stdout to be line-buffered
* add TDLS channel switch configuration
* add support for MAC address randomization in scans with nl80211
* enable HT for IBSS if supported by the driver
* add BSSID black and white lists (bssid_blacklist, bssid_whitelist)
* add support for domain_suffix_match with GnuTLS
* add OCSP stapling client support with GnuTLS
* include peer certificate in EAP events even without a separate probe
operation; old behavior can be restored with cert_in_cb=0
* add peer ceritficate alt subject name to EAP events
(CTRL-EVENT-EAP-PEER-ALT)
* add domain_match network profile parameter (similar to
domain_suffix_match, but full match is required)
* enable AP/GO mode HT Tx STBC automatically based on driver support
* add ANQP-QUERY-DONE event to provide information on ANQP parsing
status
* allow passive scanning to be forced with passive_scan=1
* add a workaround for Linux packet socket behavior when interface is in
bridge
* increase 5 GHz band preference in BSS selection (estimate SNR, if info
not available from driver; estimate maximum throughput based on common
HT/VHT/specific TX rate support)
* add INTERWORKING_ADD_NETWORK ctrl_iface command; this can be used to
implement Interworking network selection behavior in upper layers
software components
* add optional reassoc_same_bss_optim=1 (disabled by default)
optimization to avoid unnecessary Authentication frame exchange
* extend TDLS frame padding workaround to cover all packets
* allow wpa_supplicant to recover nl80211 functionality if the cfg80211
module gets removed and reloaded without restarting wpa_supplicant
* allow hostapd DFS implementation to be used in wpa_supplicant AP mode
Sat Oct 18 14:00:00 2014 stefan.bruensAATTrwth-aachen.de
- Update to 2.3
* fixed number of minor issues identified in static analyzer warnings
* fixed wfd_dev_info to be more careful and not read beyond the buffer
when parsing invalid information for P2P-DEVICE-FOUND
* extended P2P and GAS query operations to support drivers that have
maximum remain-on-channel time below 1000 ms (500 ms is the current
minimum supported value)
* added p2p_search_delay parameter to make the default p2p_find delay
configurable
* improved P2P operating channel selection for various multi-channel
concurrency cases
* fixed some TDLS failure cases to clean up driver state
* fixed dynamic interface addition cases with nl80211 to avoid adding
ifindex values to incorrect interface to skip foreign interface events
properly
* added TDLS workaround for some APs that may add extra data to the
end of a short frame
* fixed EAP-AKA\' message parser with multiple AT_KDF attributes
* added configuration option (p2p_passphrase_len) to allow longer
passphrases to be generated for P2P groups
* fixed IBSS channel configuration in some corner cases
* improved HT/VHT/QoS parameter setup for TDLS
* modified D-Bus interface for P2P peers/groups
* started to use constant time comparison for various password and hash
values to reduce possibility of any externally measurable timing
differences
* extended explicit clearing of freed memory and expired keys to avoid
keeping private data in memory longer than necessary
* added optional scan_id parameter to the SCAN command to allow manual
scan requests for active scans for specific configured SSIDs
* fixed CTRL-EVENT-REGDOM-CHANGE event init parameter value
* added option to set Hotspot 2.0 Rel 2 update_identifier in network
configuration to support external configuration
* modified Android PNO functionality to send Probe Request frames only
for hidden SSIDs (based on scan_ssid=1)
* added generic mechanism for adding vendor elements into frames at
runtime (VENDOR_ELEM_ADD, VENDOR_ELEM_GET, VENDOR_ELEM_REMOVE)
* added fields to show unrecognized vendor elements in P2P_PEER
* removed EAP-TTLS/MSCHAPv2 interoperability workaround so that
MS-CHAP2-Success is required to be present regardless of
eap_workaround configuration
* modified EAP fast session resumption to allow results to be used only
with the same network block that generated them
* extended freq_list configuration to apply for sched_scan as well as
normal scan
* modified WPS to merge mixed-WPA/WPA2 credentials from a single session
* fixed nl80211/RTM_DELLINK processing when a P2P GO interface is
removed from a bridge
* fixed number of small P2P issues to make negotiations more robust in
corner cases
* added experimental support for using temporary, random local MAC
address (mac_addr and preassoc_mac_addr parameters); this is disabled
by default (i.e., previous behavior of using permanent address is
maintained if configuration is not changed)
* added D-Bus interface for setting/clearing WFD IEs
* fixed TDLS AID configuration for VHT
* modified -m configuration file to be used only for the P2P
non-netdev management device and do not load this for the default
station interface or load the station interface configuration for
the P2P management interface
* fixed external MAC address changes while wpa_supplicant is running
* started to enable HT (if supported by the driver) for IBSS
* fixed wpa_cli action script execution to use more robust mechanism
(CVE-2014-3686)
Thu Sep 18 14:00:00 2014 schwabAATTsuse.de
- Avoid spurious dependency on /usr/bin/python due to executable doc files
Wed Aug 20 14:00:00 2014 lnusselAATTsuse.de
- fix dbus systemd activation (bnc#892683)
Thu Jun 26 14:00:00 2014 lnusselAATTsuse.de
- don\'t use systemctl enable in %post. Needs to be handled by presets.
Thu Jun 19 14:00:00 2014 glinAATTsuse.com
- Update the build config based on the new defconfig
- Remove the libnl1 requirement. It\'s not supported.
Mon Jun 16 14:00:00 2014 glinAATTsuse.com
- Update to 2.2
* added DFS indicator to get_capability freq
* added/fixed nl80211 functionality
* removed unused NFC_RX_HANDOVER_REQ and NFC_RX_HANDOVER_SEL
control interface commands (the more generic
NFC_REPORT_HANDOVER is now used)
* fixed MSCHAP UTF-8 to UCS-2 conversion for three-byte encoding
* P2P enhancements/fixes
* added phase1 network parameter options for disabling TLS v1.1
and v1.2 to allow workarounds with misbehaving AAA servers
* Interworking/Hotspot 2.0 enhancements
* fixed TDLS interoperability issues with supported operating
class in
* some deployed stations
* internal TLS implementation enhancements/fixes
* fixed PTK derivation for CCMP-256 and GCMP-256
* added \"reattach\" command for fast reassociate-back-to-same-BSS
* added \"get_capability tdls\" command
* D-Bus interface extensions/fixes
* fixed potential segmentation fault and memory leaks in WNM
neighbor report processing
* EAP-pwd fixes
* added MACsec/IEEE Std 802.1X-2010 PAE implementation
* fixed a memory leak in SAE random number generation
* fixed EAPOL-Key exchange when GCMP is used with SHA256-based
AKM
* added support for simultaneous authentication of equals (SAE)
for stronger password-based authentication with WPA2-Personal
* improved P2P negotiation and group formation robustness
* improved P2P channel selection
* added nl80211 functionality
- VHT configuration for nl80211
- MFP (IEEE 802.11w) information for nl80211 command API
- support split wiphy dump
- FT (IEEE 802.11r) with driver-based SME
- use advertised number of supported concurrent channels
- QoS Mapping configuration
* improved TDLS negotiation robustness
* added \'SCAN TYPE=ONLY\' ctrl_iface command to request manual
scan without executing roaming/network re-selection on scan
results
* added Session-Id derivation for EAP peer methods
* allow AP/Enrollee to be specified with BSSID instead of UUID
for WPS ER operations
* changed the default driver interface from wext to nl80211 if
both are included in the build
* added domain_suffix_match (and domain_suffix_match2 for Phase 2
EAP-TLS) to specify additional constraint for the server
certificate domain name
* added support for WPS+NFC updates and P2P+NFC
- Drop wpa_supplicant-driver-wext-debug.patch and
wpa_supplicant-errormsg.patch: wext is deprecated
- Enable AP mode, P2P, RSN IBSS, EAP FAST, EAP AKA, and WPS NFC
Thu May 8 14:00:00 2014 roAATTsuse.de
- use _rundir macro
Mon Sep 9 14:00:00 2013 fcrozatAATTsuse.com
- Add systemd service file, to properly track wpa_supplicant in
its own systemd service (and not in dbus one).
- Always enable systemd service, it is still dbus activated.
Wed Apr 24 14:00:00 2013 glinAATTsuse.com
- Update to 2.0
* removed Qt3-based wpa_gui (obsoleted by wpa_qui-qt4)
* removed unmaintained driver wrappers broadcom, iphone, osx,
ralink, hostap, madwifi (hostap and madwifi remain available
for hostapd; their wpa_supplicant functionality is obsoleted
by wext)
* improved debug logging (human readable event names, interface
name included in more entries)
* changed AP mode behavior to enable WPS only for open and
WPA/WPA2-Personal configuration
* improved P2P concurrency operations
- better coordination of concurrent scan and P2P search
operations
- avoid concurrent remain-on-channel operation requests by
canceling previous operations prior to starting a new one
- reject operations that would require multi-channel
concurrency if the driver does not support it
- add parameter to select whether STA or P2P connection is
preferred if the driver cannot support both at the same time
- allow driver to indicate channel changes
- added optional delay= parameter
for p2p_find to avoid taking all radio resources
- use 500 ms p2p_find search delay by default during concurrent
operations
- allow all channels in GO Negotiation if the driver supports
multi-channel concurrency
* added number of small changes to make it easier for static
analyzers to understand the implementation
* fixed number of small bugs (see git logs for more details)
* nl80211: number of updates to use new cfg80211/nl80211
functionality
- replace monitor interface with nl80211 commands for AP mode
- additional information for driver-based AP SME
- STA entry authorization in RSN IBSS
* EAP-pwd:
- fixed KDF for group 21 and zero-padding
- added support for fragmentation
- increased maximum number of hunting-and-pecking iterations
* avoid excessive Probe Response retries for broadcast Probe
Request frames (only with drivers using wpa_supplicant AP mode
SME/MLME)
* added \"GET country\" ctrl_iface command
* do not save an invalid network block in wpa_supplicant.conf to
avoid problems reading the file on next start
* send STA connected/disconnected ctrl_iface events to both the
P2P group and parent interfaces
* added preliminary support for using TLS v1.2 (CONFIG_TLSV12=y)
* added \"SET pno <1/0>\" ctrl_iface command to start/stop
preferred network offload with sched_scan driver command
* merged in number of changes from Android repository for P2P,
nl80211, and build parameters
* changed P2P GO mode configuration to use driver capabilities
to automatically enable HT operations when supported
* added \"wpa_cli status wps\" command to fetch WPA2-Personal
passhrase for WPS use cases in AP mode
* EAP-AKA: keep pseudonym identity across EAP exchanges to match
EAP-SIM behavior
* improved reassociation behavior in cases where association is
rejected or when an AP disconnects us to handle common load
balancing mechanisms
- try to avoid extra scans when the needed information is
available
* added optional \"join\" argument for p2p_prov_disc ctrl_iface
command
* added group ifname to P2P-PROV-DISC-
* events
* added P2P Device Address to AP-STA-DISCONNECTED event and use
p2p_dev_addr parameter name with AP-STA-CONNECTED
* added workarounds for WPS PBC overlap detection for some P2P
use cases where deployed stations work incorrectly
* optimize WPS connection speed by disconnecting prior to WPS
scan and by using single channel scans when AP channel is
known
* PCSC and SIM/USIM improvements:
- accept 0x67 (Wrong length) as a response to READ RECORD to
fix issues with some USIM cards
- try to read MNC length from SIM/USIM
- build realm according to 3GPP TS 23.003 with identity from
the SIM
- allow T1 protocol to be enabled
* added more WPS and P2P information available through D-Bus
* improve P2P negotiation robustness
- extra waits to get ACK frames through
- longer timeouts for cases where deployed devices have been
identified have issues meeting the specification
requirements
- more retries for some P2P frames
- handle race conditions in GO Negotiation start by both
devices
- ignore unexpected GO Negotiation Response frame
* added support for libnl 3.2 and newer
* added P2P persistent group info to P2P_PEER data
* maintain a list of P2P Clients for persistent group on GO
* AP: increased initial group key handshake retransmit timeout to
500 ms
* added optional dev_id parameter for p2p_find
* added P2P-FIND-STOPPED ctrl_iface event
* fixed issues in WPA/RSN element validation when roaming with
ap_scan=1 and driver-based BSS selection
* do not expire P2P peer entries while connected with the peer in a
group
* fixed WSC element inclusion in cases where P2P is disabled
* AP: added a WPS workaround for mixed mode AP Settings with
Windows 7
* EAP-SIM: fixed AT_COUNTER_TOO_SMALL use
* EAP-SIM/AKA: append realm to pseudonym identity
* EAP-SIM/AKA: store pseudonym identity in network configuration
to allow it to persist over multiple EAP sessions and
wpa_supplicant restarts
* EAP-AKA\': updated to RFC 5448 (username prefixes changed);
note: this breaks interoperability with older versions
* added support for WFA Hotspot 2.0
- GAS/ANQP to fetch network information
- credential configuration and automatic network selections
based on credential match with ANQP information
* limited PMKSA cache entries to be used only with the network
context that was used to create them
* improved PMKSA cache expiration to avoid unnecessary
disconnections
* adjusted bgscan_simple fast-scan backoff to avoid too frequent
background scans
* removed ctrl_iface event on P2P PD Response in join-group case
* added option to fetch BSS table entry based on P2P Device
Address (\"BSS p2p_dev_addr=\")
* added BSS entry age to ctrl_iface BSS command output
* added optional MASK=0xH option for ctrl_iface BSS command to
select which fields are included in the response
* added optional RANGE=ALL|N1-N2 option for ctrl_iface BSS
command to fetch information about several BSSes in one call
* simplified licensing terms by selecting the BSD license as the
only alternative
* added \"P2P_SET disallow_freq \" ctrl_iface command
to disable channels from P2P use
* added p2p_pref_chan configuration parameter to allow preferred
P2P channels to be specified
* added support for advertising immediate availability of a WPS
credential for P2P use cases
* optimized scan operations for P2P use cases (use single channel
scan for a specific SSID when possible)
* EAP-TTLS: fixed peer challenge generation for MSCHAPv2
* SME: do not use reassociation after explicit disconnection
request (local or a notification from an AP)
* added support for sending debug info to Linux tracing (-T on
command line)
* added support for using Deauthentication reason code 3 as an
indication of P2P group termination
* added wps_vendor_ext_m1 configuration parameter to allow
vendor specific attributes to be added to WPS M1
* started using separate TLS library context for tunneled TLS
(EAP-PEAP/TLS, EAP-TTLS/TLS, EAP-FAST/TLS) to support different
CA certificate configuration between Phase 1 and Phase 2
* added optional \"auto\" parameter for p2p_connect to request
automatic GO Negotiation vs. join-a-group selection
* added disabled_scan_offload parameter to disable automatic scan
offloading (sched_scan)
* added optional persistent= parameter for
p2p_connect to allow forcing of a specific SSID/passphrase for
GO Negotiation
* added support for OBSS scan requests and 20/40 BSS coexistence
reports
* reject PD Request for unknown group
* removed scripts and notes related to Windows binary releases
(which have not been used starting from 1.x)
* added initial support for WNM operations
- Keep-alive based on BSS max idle period
- WNM-Sleep Mode
- minimal BSS Transition Management processing
* added autoscan module to control scanning behavior while not
connected
- autoscan_periodic and autoscan_exponential modules
* added new WPS NFC ctrl_iface mechanism
- added initial support NFC connection handover
- removed obsoleted WPS_OOB command (including support for
deprecated UFD config_method)
* added optional framework for external password storage
(\"ext:\")
* wpa_cli: added optional support for controlling wpa_supplicant
remotely over UDP (CONFIG_CTRL_IFACE=udp-remote) for testing
purposes
* wpa_cli: extended tab completion to more commands
* changed SSID output to use printf-escaped strings instead of
masking of non-ASCII characters
- SSID can now be configured in the same format:
ssid=P\"abc\\x00test\"
* removed default ACM=1 from AC_VO and AC_VI
* added optional \"ht40\" argument for P2P ctrl_iface commands to
allow 40 MHz channels to be requested on the 5 GHz band
* added optional parameters for p2p_invite command to specify
channel when reinvoking a persistent group as the GO
* improved FIPS mode builds with OpenSSL
- \"make fips\" with CONFIG_FIPS=y to build wpa_supplicant with
the OpenSSL FIPS object module
- replace low level OpenSSL AES API calls to use EVP
- use OpenSSL keying material exporter when possible
- do not export TLS keys in FIPS mode
- remove MD5 from CONFIG_FIPS=y builds
- use OpenSSL function for PKBDF2 passphrase-to-PSK
- use OpenSSL HMAC implementation
- mix RAND_bytes() output into random_get_bytes() to force
OpenSSL DRBG to be used in FIPS mode
- use OpenSSL CMAC implementation
* added mechanism to disable TLS Session Ticket extension
- a workaround for servers that do not support TLS extensions
that was enabled by default in recent OpenSSL versions
- tls_disable_session_ticket=1
- automatically disable TLS Session Ticket extension by default
when using EAP-TLS/PEAP/TTLS (i.e., only use it with
EAP-FAST)
* changed VENDOR-TEST EAP method to use proper private
enterprise number (this will not interoperate with older
versions)
* disable network block temporarily on authentication failures
* improved WPS AP selection during WPS PIN iteration
* added support for configuring GCMP cipher for IEEE 802.11ad
* added support for Wi-Fi Display extensions
- WFD_SUBELEMENT_SET ctrl_iface command to configure WFD
subelements
- SET wifi_display <0/1> to disable/enable WFD support
- WFD service discovery
- an external program is needed to manage the audio/video
streaming and codecs
* optimized scan result use for network selection
- use the internal BSS table instead of raw scan results
- allow unnecessary scans to be skipped if fresh information
is available (e.g., after GAS/ANQP round for Interworking)
* added support for 256-bit AES with internal TLS implementation
* allow peer to propose channel in P2P invitation process for a
persistent group
* added disallow_aps parameter to allow BSSIDs/SSIDs to be
disallowed from network selection
* re-enable the networks disabled during WPS operations
* allow P2P functionality to be disabled per interface
(p2p_disabled=1)
* added secondary device types into P2P_PEER output
* added an option to disable use of a separate P2P group
interface (p2p_no_group_iface=1)
* fixed P2P Bonjour SD to match entries with both compressed and
not compressed domain name format and support multiple Bonjour
PTR matches for the same key
* use deauthentication instead of disassociation for all
disconnection operations; this removes the now unused
disassociate() wpa_driver_ops callback
* optimized PSK generation on P2P GO by caching results to avoid
multiple PBKDF2 operations
* added okc=1 global configuration parameter to allow OKC to be
enabled by default for all network blocks
* added a workaround for WPS PBC session overlap detection to
avoid interop issues with deployed station implementations
that do not remove active PBC indication from Probe Request
frames properly
* added basic support for 60 GHz band
* extend EAPOL frames processing workaround for roaming cases
(postpone processing of unexpected EAPOL frame until
association event to handle reordered events)
- Drop upstreamed wpa_supplicant-libnl3.patch
- Disable obsolete Ralink driver
Tue Dec 11 13:00:00 2012 glinAATTsuse.com
- Update to 1.1
* Fix EAPOL supplicant port authorization with PMKSA caching.
* Fix EAPOL processing when STA switches between multi-BSSes.
* Fix EAP-FAST with OpenSSL 1.0.1.
* EAP-pwd: Increase maximum number of hunting-and-pecking
iterations, which results in less authentication attempts
failing.
* Set state to DISCONNECTED on AP creation errors. Previously the
supplicant would stay in SCANNING state forever.
* Fix REMOVE_NETWORK to not run operations with invalid
current_ssid.
* EAP-SIM peer: Fix AT_COUNTER_TOO_SMALL use.
* Interworking: Fix PLMN matching with multiple entries to compare
all entries, not just the first one.
* Handle long configuration file lines more gracefully.
* Fix adding extra IEs in sched scan.
* PMKSA: Set cur_pmksa pointer during initial association.
* PMKSA: Do not evict the active cache entry when adding new ones.
* Set state consistently to DISCONNECTED on auth/assoc failures.
* Fix BSSID enforcement with driver-based BSS selection. Set BSSID
and channel when the network block has an explicit bssid
parameter to select which BSS is to be used.
* wpa_gui: Fix compilation with gcc/g++ 4.7.
* EAP-AKA\'
- Update to RFC 5448 in the leading characters used in the
username. This will make EAP-AKA\' not interoperate between the
earlier draft version and the new version.
- Fix SIM/USIM determination to support EAP-AKA\'.
* dbus:
- Add global capabilities property.
- Fix bss_expire_count getter, which was returning the wrong
value.
- P2P: Remove network_object dictionary entry from signal
GroupStarted.
- Fix D-Bus build without ctrl_iface.
* WPS:
- Fix nonce comparisons to compare all bytes, not just the first
byte.
- Fix NFC password token building with WPS 2.0 to avoid wpabuf
overflow and application abort if NFC out-of-band mechanism is
used with WPS 2.0 enabled.
- Fix cleanup of WPS operations (by clearing them) in
WPA_SCANNING and WPA_DISCONNECTED states.
- Fix issue with BSSID filter handling that could cause only a
single one of the available BSSes to be available or could
cause issues connecting.
- Fix overlapping memcpy on WPS interface addition.
* P2P:
- Remove channel 14 from supported P2P channels.
- Fix Provision Discovery retries on delay in off channel
transmission, to avoid unnecessary retries.
- Limit maximum number of stored P2P clients (the
p2p_client_list parameter) to 100.
- Improve p2p_client_list updates in configuration file,
reording entries so that the most recently added values are
maintained in the list if the list gets truncated due to
size.
- Fix Provision Discovery retries during p2p_find by making the
p2p_find case behave consistently with the limited retry
behavior used with Provision Discovery retries in the IDLE
state.
- Fix P2P Client Discoverability bit updates so that the bit is
only updated based on P2P Group Info attribute from a GO.
- Fix GO Negotiation race condition where both devices may
believe they are the GO. (Ignore unexpected GO Neg Response
if we have already sent GO Neg Response.)
- Deinitialize global P2P context on P2P management interface
removal.
- Wait 100 ms if driver fails to start listen operation. This
is a workaround for some drivers that may accept the
remain-on-channel command, but instead of indicating start
event for remain-on-channel, just indicate that the operation
has been cancelled immediately.
- Clone max_sta_num parameter for group interfaces, allowing
this parameter set in the main config file to apply to
dynamically created P2P group interfaces.
- Fix Device ID matching for Probe Request frames, which was
checking only the first octet of the P2P Device Address.
- Do not update peer Listen channel based on PD Request
Invitation Request frames (just on Probe Response frames).
- Fix p2p_listen to disallow scheduling a new after scan
operation in the case where a p2p_connect operation is
pending.
- Remove upstreamed wpa_supplicant-gcc47.patch
- Enable background scan to improve roaming
- Build driver with libnl3 (wpa_supplicant-libnl3.patch)
Tue May 15 14:00:00 2012 glinAATTsuse.com
- Update to 1.0
* Delay STA entry removal until Deauth/Disassoc TX status
in AP mode. This allows the driver to use PS buffering of
Deauthentication and Disassociation frames when the STA
is in power save sleep. Only available with drivers that
provide TX status events for Deauth/Disassoc frames
(nl80211).
* Drop oldest unknown BSS table entries first. This makes
it less likely to hit connection issues in environments
with huge number of visible APs.
* Add systemd support.
* Add support for setting the syslog facility from the
config file at build time.
* atheros: Add support for IEEE 802.11w configuration.
* AP mode: Allow enable HT20 if driver supports it, by
setting the config parameter ieee80211n.
* Allow AP mode to disconnect STAs based on low ACK
condition (when the data connection is not working
properly, e.g., due to the STA going outside the range
of the AP).
* nl80211:
- Support GTK rekey offload.
- Support PMKSA candidate events. This adds support for
RSN pre-authentication with nl80211 interface and
drivers that handle roaming internally.
* Improved dbus interface
* New wpa_cli commands to setup the scan interval and
to support P2P and WPS/WPS ER
* AP mode: Add max_num_sta config option, which can be used
to limit the number of stations allowed to connect to the
AP.
* wext: Increase scan timeout from 5 to 10 seconds.
* Allow an external program to manage the BSS blacklist
and display its current contents.
* WPS:
- Add wpa_cli wps_pin get command for generating random
PINs. This can be used in a UI to generate a PIN
without starting WPS (or P2P) operation.
- Set RF bands based on driver capabilities, instead of
hardcoding them.
- Add mechanism for indicating non-standard WPS errors.
- Add wps_ap_pin cli command for wpa_supplicant AP mode.
- Add wps_check_pin cli command for processing PIN from
user input. UIs can use this command to process a PIN
entered by a user and to validate the checksum digit
(if present).
- Cancel WPS operation on PBC session overlap detection.
- New wps_cancel command in wpa_cli will cancel a
pending WPS operation.
- wpa_cli action: Add WPS_EVENT_SUCCESS and
WPS_EVENT_FAIL handlers.
- Trigger WPS config update on Manufacturer, Model Name,
Model Number, and Serial Number changes.
- Fragment size is now configurable for EAP-WSC peer.
Use wpa_cli set wps_fragment_size .
- Disable AP PIN after 10 consecutive failures. Slow down
attacks on failures up to 10.
- Allow AP to start in Enrollee mode without AP PIN for
probing, to be compatible with Windows 7.
- Add Config Error into WPS-FAIL events to provide more
info to the user on how to resolve the issue.
- Label and Display config methods are not allowed to be
enabled at the same time, since it is unclear which
PIN to use if both methods are advertised.
- When controlling multiple interfaces:
- apply WPS commands to all interfaces configured to
use WPS
- apply WPS config changes to all interfaces that use
WPS
- when an attack is detected on any interface, disable
AP PIN on all interfaces
* WPS ER:
- Add special AP Setup Locked mode to allow read only ER.
- Show SetSelectedRegistrar events as ctrl_iface events
- Add wps_er_set_config to enroll a network based on a
local network configuration block instead of having to
(re-)learn the current AP settings with wps_er_learn.
- Allow AP filtering based on IP address, add ctrl_iface
event for learned AP settings, add wps_er_config
command to configure an AP.
* Add support for WPS 2.0
* TDLS:
- Propogate TDLS related nl80211 capability flags from
kernel and add them as driver capability flags. If the
driver doesn\'t support capabilities, assume TDLS is
supported internally. When TDLS is explicitly not
supported, disable all user facing TDLS operations.
- Allow TDLS to be disabled at runtime.
- Honor AP TDLS settings that prohibit/allow TDLS.
- Add a special testing feature for changing TDLS
behavior.
- Add support for TDLS 802.11z.
* wlantest: Add a tool wlantest for IEEE802.11 protocol
testing. wlantest can be used to capture frames from a
monitor interface for realtime capturing or from pcap
files for offline analysis.
* bgscan learn: Add new bgscan that learns BSS information
based on previous scans, and uses that information to
dynamically generate the list of channels for background
scans.
* Add a new debug message level for excessive information.
* TLS: Add support for tls_disable_time_checks=1 in client
mode.
* Improved internal TLS
* Add RFKill support by adding an interface state
\"disabled\".
* Reorder some IEs to get closer to IEEE 802.11 standard.
Move WMM into end of Beacon, Probe Resp and (Re)Assoc
Resp frames. Move HT IEs to be later in (Re)Assoc Resp.
* Wi-Fi Direct support
- Remove wpa_supplicant-dbus-events.patch (merged upstream)
- Remove wpa_supplicant-probed-cert-dbus-signal.patch (merged
upstream)
Sat Mar 17 13:00:00 2012 dimstarAATTopensuse.org
- Add wpa_supplicant-gcc47.patch: Fix build with gcc 4.7.
Tue Jan 10 13:00:00 2012 glinAATTsuse.com
- Add wpa_supplicant-probed-cert-dbus-signal.patch to emit a D-Bus
signal when the AP returned the certificate of the RADIUS server
(bnc#574266)
Mon Oct 10 14:00:00 2011 lnusselAATTsuse.de
- use same exec line in fi.w1.wpa_supplicant1.service as in
fi.epitest.hostap.WPASupplicant.service
- fix build on older distros
- fix not using RPM_OPT_FLAGS
- use %_smp_mflags
Fri Sep 16 14:00:00 2011 jengelhAATTmedozas.de
- Select libnl-1_1-devel
Wed Aug 31 14:00:00 2011 vbotkaAATTsuse.de
- %ghost directive for /var/run/wpa_supplicant added for tmpfs
(bnc 710281)
Wed Mar 16 13:00:00 2011 dimstarAATTopensuse.org
- Add wpa_supplicant-dbus-events.patch: Emit property changed
events when adding/removing BSSes. Required by NetworkManager
0.9 beta1 and later.
- Also install fi.w1.wpa_supplicant1.service, which was added as
source5, sourced from the wpa_supplicant source code, with
modified exec line pointing to /usr/sbin instead of /sbin.
Tue Sep 7 14:00:00 2010 vbotkaAATTsuse.de
- update to 0.7.3
* fixed fallback from failed PMKSA caching into full EAP authentication
[Bug 355]
* fixed issue with early D-Bus signals during initialization
* fixed X.509 name handling in internal TLS
* fixed WPS ER to use corrent Enrollee MAC Address in Credential
* fixed scanning routines ot improve AP selection for WPS
* added WPS workaround for open networks
* fixed WPS Diffie-Hellman derivation to use correct public key length
* fixed wpa_supplicant AP mode operations to ignore Supplicant and
scan result events
* improved SME operations with nl80211
* fixed WPS ER event_id handling in some cases
* fixed some issues with bgscan simple to avoid unnecessary scans
* fixed issue with l2_packet_ndis overlapped writes corrupting stack
[Bug 328]
* updated WinPcap to the latest stable version 4.1.2 in Windows
installer
update to 0.7.2
* nl80211: fixed number of issues with roaming
* avoid unnecessary roaming if multiple APs with similar signal
strength are present in scan results
* add TLS client events and server probing to ease design of
automatic detection of EAP parameters
* add option for server certificate matching (SHA256 hash of the
certificate) instead of trusted CA certificate configuration
* bsd: Cleaned up driver wrapper and added various low-level
configuration options
* wpa_gui-qt4: do not show too frequent WPS AP available events as
tray messages
* TNC: fixed issues with fragmentation
* EAP-TNC: add Flags field into fragment acknowledgement (needed to
interoperate with other implementations; may potentially breaks
compatibility with older wpa_supplicant/hostapd versions)
* wpa_cli: added option for using a separate process to receive event
messages to reduce latency in showing these
(CFLAGS += -DCONFIG_WPA_CLI_FORK=y in .config to enable this)
* maximum BSS table size can now be configured (bss_max_count)
* BSSes to be included in the BSS table can be filtered based on
configured SSIDs to save memory (filter_ssids)
* fix number of issues with IEEE 802.11r/FT; this version is not
backwards compatible with old versions
* nl80211: add support for IEEE 802.11r/FT protocol (both over-the-air
and over-the-DS)
* add freq_list network configuration parameter to allow the AP
selection to filter out entries based on the operating channel
* add signal strength change events for bgscan; this allows more
dynamic changes to background scanning interval based on changes in
the signal strength with the current AP; this improves roaming within
ESS quite a bit, e.g., with bgscan=\"simple:30:-45:300\" in the network
configuration block to request background scans less frequently when
signal strength remains good and to automatically trigger background
scans whenever signal strength drops noticeably
(this is currently only available with nl80211)
* add BSSID and reason code (if available) to disconnect event messages
* wpa_gui-qt4: more complete support for translating the GUI with
linguist and add German translation
* fix DH padding with internal crypto code (mainly, for WPS)
* do not trigger initial scan automatically anymore if there are no
enabled networks
Fri May 28 14:00:00 2010 vbotkaAATTsuse.de
- Fix fallback from failed PMKSA caching into full EAP authentication
(bnc 601501)
Sun Jan 31 13:00:00 2010 ajAATTsuse.de
- Update to 0.7.1 (full changelog in wpa_supplicant/ChangeLog):
* Cleanup of interfaces
* dbus: added new DBus interface (fi.w1.wpa_supplicant1)
* driver_nl80211: multiple updates to provide support for new Linux
nl80211/mac80211 functionality
- Remove wpa_supplicant-dbus-iface-segfault-fix.patch, does not apply
at all.
- Remove wpa_supplicant-dbus-reset-eapol.patch (merged upstream).
- Disable patches that do not apply anymore but are not merged.
Mon Sep 28 14:00:00 2009 lnusselAATTsuse.de
- simplify dbus config, allow introspection
Mon Sep 7 14:00:00 2009 claes.backstromAATTfsfe.org
- Added rotation of log file with logrotate (bnc#508041)
Tue May 12 14:00:00 2009 dmuellerAATTsuse.de
- reenable logfile writing support to make d-bus activation work
again (bnc#502957)
Tue Apr 7 14:00:00 2009 hschaaAATTsuse.de
- Enable ralink driver (bnc#481380)
- Enable nl80211 driver (bnc#485453)
- Rebase all SUSE patches to 0.6.9
- Remove upstreamed patches
- Update to 0.6.9
* driver_ndis: add PAE group address to the multicast address list to
fix wired IEEE 802.1X authentication
* fixed IEEE 802.11r key derivation function to match with the standard
(note: this breaks interoperability with previous version) [Bug 303]
* increased wpa_cli ping interval to 5 seconds and made this
configurable with a new command line options (-G)
* fixed scan buffer processing with WEXT to handle up to 65535
byte result buffer (previously, limited to 32768 bytes)
* added support for Wi-Fi Protected Setup (WPS)
(wpa_supplicant can now be configured to act as a WPS Enrollee to
enroll credentials for a network using PIN and PBC methods; in
addition, wpa_supplicant can act as a wireless WPS Registrar to
configure an AP); WPS support can be enabled by adding CONFIG_WPS=y
into .config and setting the runtime configuration variables in
wpa_supplicant.conf (see WPS section in the example configuration
file); new wpa_cli commands wps_pin, wps_pbc, and wps_reg are used to
manage WPS negotiation; see README-WPS for more details
* added support for EAP-AKA\' (draft-arkko-eap-aka-kdf)
* added support for using driver_test over UDP socket
* fixed PEAPv0 Cryptobinding interoperability issue with Windows Server
2008 NPS; optional cryptobinding is now enabled (again) by default
* fixed PSK editing in wpa_gui
* changed EAP-GPSK to use the IANA assigned EAP method type 51
* added a Windows installer that includes WinPcap and all the needed
DLLs; in addition, it set up the registry automatically so that user
will only need start wpa_gui to get prompted to start the wpasvc
servide and add a new interface if needed through wpa_gui dialog
* updated management frame protection to use IEEE 802.11w/D7.0
* added Milenage SIM/USIM emulator for EAP-SIM/EAP-AKA
(can be used to simulate test SIM/USIM card with a known private key;
enable with CONFIG_SIM_SIMULATOR=y/CONFIG_USIM_SIMULATOR=y in .config
and password=\"Ki:OPc\"/password=\"Ki:OPc:SQN\" in network configuration)
* added a new network configuration option, wpa_ptk_rekey, that can be
used to enforce frequent PTK rekeying, e.g., to mitigate some attacks
against TKIP deficiencies
* added an optional mitigation mechanism for certain attacks against
TKIP by delaying Michael MIC error reports by a random amount of time
between 0 and 60 seconds; this can be enabled with a build option
CONFIG_DELAYED_MIC_ERROR_REPORT=y in .config
* fixed EAP-AKA to use RES Length field in AT_RES as length in bits,
not bytes
* updated OpenSSL code for EAP-FAST to use an updated version of the
session ticket overriding API that was included into the upstream
OpenSSL 0.9.9 tree on 2008-11-15 (no additional OpenSSL patch is
needed with that version anymore)
* updated userspace MLME instructions to match with the current Linux
mac80211 implementation; please also note that this can only be used
with driver_nl80211.c (the old code from driver_wext.c was removed)
* added support (Linux only) for RoboSwitch chipsets (often found in
consumer grade routers); driver interface \'roboswitch\'
* fixed canceling of PMKSA caching when using drivers that generate
RSN IE and refuse to drop PMKIDs that wpa_supplicant does not know
about
* added support for SHA-256 as X.509 certificate digest when using the
internal X.509/TLSv1 implementation
* updated management frame protection to use IEEE 802.11w/D6.0
* added support for using SHA256-based stronger key derivation for WPA2
(IEEE 802.11w)
* fixed FT (IEEE 802.11r) authentication after a failed association to
use correct FTIE
* added support for configuring Phase 2 (inner/tunneled) authentication
method with wpa_gui-qt4
* added support for EAP Sequences in EAP-FAST Phase 2
* added support for using TNC with EAP-FAST
* added driver_ps3 for the PS3 Linux wireless driver
* added support for optional cryptobinding with PEAPv0
* fixed the OpenSSL patches (0.9.8g and 0.9.9) for EAP-FAST to
allow fallback to full handshake if server rejects PAC-Opaque
* added fragmentation support for EAP-TNC
* added support for parsing PKCS #8 formatted private keys into the
internal TLS implementation (both PKCS #1 RSA key and PKCS #8
encapsulated RSA key can now be used)
* added option of using faster, but larger, routines in the internal
LibTomMath (for internal TLS implementation) to speed up DH and RSA
calculations (CONFIG_INTERNAL_LIBTOMMATH_FAST=y)
* fixed race condition between disassociation event and group key
handshake to avoid getting stuck in incorrect state [Bug 261]
* fixed opportunistic key caching (proactive_key_caching)
Sun Mar 1 13:00:00 2009 cooloAATTsuse.de
- fix compilation with gcc 4.4
