Changelog for sdparm-debuginfo-1.10-lp150.1.7.x86_64.rpm :

* Wed Aug 24 2016 alexander_naumovAATTopensuse.org- Update to version 1.10
* add --inhex=FN option for decoding without device present, FN is interpreted as response to mode sense(10) command
* add --raw option to interpret FN as binary (def: ASCII hex)
* add --pdt=PDT option for use with --inhex=FN
* --quiet used twice hides changeable, default + saved
* add IO advice hints grouping mode page (sbc4r06, 8)
* add Unit serial number VPD page specific sanity check
* add NO_PI_CHK to Supported block lengths and protection types VPD page
* add Background operation control mpage (sbc4r07)
* Read-write error recovery mpage: add Misaligned writes reporting field (MWR)
* sync tape mpages with ssc5r02
* add Block limits extension VPD page
* add Device constituents VPD page
* add LB protection VPD page (ssc5r02a)
* LB provisioning VPD page: expand LBPRZ, add Minimum and Threshold percentage fields
* device identification VPD page: add decoding for locally assigned UUIDs (spc5r08)
* the --inhex=FN option together with --inquiry decodes FN as a single VPD page
* improve lto5 and lto6 vendor mpage support
* sync to spc5r08 and sbc4r10
* add SAS G5 (22.5 Gbps) settings (spl4r06)
* point svn:externals to rev 663 of sg3_utils
* upgrade automake to version 1.15 (U15.10)
* autogen.sh: upgrade to buildconf 20091223 version
* Sun Dec 28 2014 p.drouandAATTgmail.com- Update to version 1.09 + decode Third Party Copy VPD page + Supported block lengths and protection types (sbc4r01) + Block device characteristics extension VPD pages added + zoned block device characterics VPD page added (zbc-r01c) + fix manufacturer-assigned serial number VPD page length + device id VPD: T10 vendor identification designator clean up + block device characteristics VPD: add ZONED (sbc4r04) + SAS/SPL disconnect-reconnect mpage: expand + SAS protocol specific port mpage: add MAXR field (spl4r01) + standard inquiry response (sinq): add LU_CONG + change ibm vendor code to lto5 and lto6 + point svn:externals to rev 620 of sg3_utils + upgrade automake to version 1.14.1 + configure: add --disable-libsgutils so build bypasses that library if present + win32: some --wscan and compile fixes
* Wed Oct 23 2013 p.drouandAATTgmail.com- Remove %fillup_prereq and %insserv_prereq; package doesn\'t provide any sysvinit script
* Thu Jun 13 2013 jengelhAATTinai.de- Update to new upstream release 1.08
* New utilities: scsi_ch_swp, sas_disk_blink
* Tracked changes at t10.org since January 2012:
* device id VPD: add protocol specific port identifier
* control extension mpage: add max sense data length
* power condition mpage: FIDCPC->CCF_IDLE, FSBCPC->CCF_STAND, FSTCPC->CCF_STOPP (spc4r34+)
* caching mpage: add SYNC_PROG field (sbc3r33)
* block device characteristics VPD page additions sbc3r34
* extended inquiry vpd page: add max supported sense data length
* protocol-specific port information VPD page for SAS SSP, persistent connection (spl3r2), power disable (spl3r3)
* allow --readonly with --set= and --clear=
* add placeholder for third party copy VPD page
* supply more information if a UA occurs- Normalized install procedure- Build with libsgutils support
* Sun Apr 22 2012 puzelAATTsuse.com- Update to version 1.07 - LB provisioning + Block limits VPD pages to sbc3r27 - Enhanced phy control page: optical mode enabled (spl-r07) - Phy control and discover page: sync to spl2r02 - sync with spc4r31+32 (handle status good with sense) - extented inquiry VPD: add POA_SUP, HRA_SUP and VSA_SUP - application tag mode page subcode 0xf0->0x2 (sbc3r28) - add \'sinq\' pseudo VPD page for standard inquiry response - add power consumption mode and VPD pages (spc4r33) - point out some mode page numbers are vendor specific
* Tue May 24 2011 dimstarAATTopensuse.org- Update to version 1.06: + allow upper and lower case in field, (mode and vpd) page, vendor, transport or command matching + control mode page: add ATMPE and RWWP fields (spc4r27) + extended inquiry vpd page: add extended self test completion minutes field (spc4r27) + power control mode page: PM_BG_PRECEDENCE field (spc4r24) - FIDCPC, FSBCPC, FSTCPC fields (spc4r25) + sbc3r25 renames \'thin\' provisioning\' to \'logical block provisioning\'; changes mode+vpd page and field names - add Application tag mode page - add SITPUA bit to logical block provisioning mode page + fix \'-eal\' problem with vendor pages + point svn:externals to rev 334 of sg3_utils
* Fri Aug 13 2010 dimstarAATTopensuse.org- Update to version 1.05: + add \'--readonly\' option especially for \'-C start\' and \'-C stop\' on ATA disks. + Control mode page updates (spc4r23) + add Control data protection mode page (ssc4r01) + block device characteristics VPD page: decode form factor + extended inquiry VPD page: activate_microcode+r_sup (spc4r23) + Automation device serial number and Data transfer device element address VPD pages (ssc4r01) + add SBC Referrals VPD page (sbc3r22) + expand SBC Thin provisioning VPD page (sbc3r22) + expand SBC Block limits VPD page (sbc3r22) + SAS-2.1 specification split, upper layers placed in SPL - add enable_slumber and enable_partial fields to Enhanced phy control mode page + add AM_MAINTAINER_MODE to configure.ac to lessen build issues + build infrastructure change to use libsgutils2 if available- Changes from version 1.04: + add SAT ATA Power condition mode page (sat2r06) + add SBC Thin provisioning mode page (sbc3r20) + add SBC Thin provisioning VPD page (sbc3r20) + sync with spc4r21 + add Power condition, update extended inquiry VPD pages + smc3: add Device capabilities + Extended device capabilities + Transport geometry parameters mode pages + prepare for Thin provisioning VPD and mode pages + expand block limits VPD page + update Power condition mode page + rename SAS-2 phy mode page to Enhanced phy control (SAS) + add ADC mode (sub)page place holders + print mode page descriptors in full in more contexts + add linux bsg support + scripts/sas_disk_blink: moved here from sg3_utils package + rework the \'-w\' option (win32) per sg_scan in sg3_utils + change SDPARM_
* constants to SG_LIB_
* + remove sdparm.html, refer to its url in sdparm.8 + sdparm.spec: correction to configure call
* Tue Aug 12 2008 garloffAATTsuse.de- Update to sdparm-1.03:
* supports more than one device on command linx
* speed[=val] and profile commands for MMC
* Extended Inquiry VPD page updated (spc4r15)
* SAS protocol-specific port mpage (add CAWT, RTOL)
* minor cleanups
* Fri May 23 2008 hareAATTsuse.de- Using \'Provides\' keyword to clean update dependency.
* Thu Apr 24 2008 hareAATTsuse.de- Split off from the original scsi package.